







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Fence Installation: The Ventura Owner’s Guide
KraftMaid fence installation in Ventura typically runs $3,500 – $9,000 for a full perimeter job, depending on fence height, gate hardware, and whether we’re replacing rotted posts or setting new ones. Most homeowners call us after a windstorm or a fence post gives out and takes a whole section down with it. Sometimes it’s a gate that won’t latch anymore, and the hinges have pulled so far out of the post that you can see daylight through the bolt holes.
Sawyer Remodel Ventura is an independent contractor, not affiliated with KraftMaid, but we install and repair fences every week throughout Ventura, Midtown, and the hills above town. If you have a KraftMaid fence product that’s failing, we’ll match the existing style, tell you straight whether the post or the panel is worth saving, and put the price in writing before we touch a single board.
Which KraftMaid Models This Applies To

KraftMaid is primarily known for cabinetry, but their fence and gate hardware line shows up in a lot of Ventura backyards, especially in homes built between 2005 and 2015. The compatibility question that actually matters is not the KraftMaid model number stamped on a gate latch, it’s the fence system itself: post spacing, rail width, and the picket profile.
The most common KraftMaid fence hardware we see includes their heavy-duty gate hinges (the black powder-coated ones with the anti-sag bracket) and their spring-loaded latch kits. When those fail, the fix usually means matching a new hinge to the rail width, not hunting down a KraftMaid part number. We stock quality aftermarket equivalents that hold up better in Ventura’s salt air than the originals. Coastal humidity chews through zinc-plated hardware faster than anything else, so if you’re west of the 101, plan on stainless or high-grade powder coat.
Quick ID tip: a KraftMaid fence panel typically spaces its pickets 3 ¾ inches apart on center, and the bottom rail sits 2 inches off the ground. If that matches what you have, we can almost always salvage the good sections and match the look with new pickets that won’t stick out.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Fence Installation Is Failing
- Posts leaning 10 degrees or more. This usually means the post base rotted below grade or the concrete footer cracked. In Ventura’s clay-heavy East End soil, winter rains swell the ground and heave posts that were never set deep enough.
- Gate dragging on the ground or refusing to latch. The anti-sag bracket on the hinge has stretched, or the bottom hinge screws have stripped out of the post. You can usually see the gate dip a half inch when it’s open.
- Pickets splitting at the top rail. Thermal cycling plus dry Santa Ana winds will do this. Once a picket splits, moisture gets in and the split runs down to the next screw hole.
- White or green crust at the base of posts. That’s rot and mildew working its way up the post. By the time you see it, the bottom 4 to 6 inches are likely soft.
- Panels rattling hard in wind. Wind coming through the Ventura Avenue corridor puts real lateral load on fence panels. If a section bangs like a screen door, the rail-to-post brackets are loose or the posts themselves are moving.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A full KraftMaid fence installation in Ventura runs $3,500 – $9,000. A repair job, where we pull one rotted post and reset it or replace three panels, usually lands between $500 and $1,500. The spread comes down to how many posts we’re setting, whether the old concrete footers have to be jackhammered out, and how much gate hardware you need replaced.
Every quote from us is a written line-item price before work starts. You’ll see the cost of posts, concrete, pickets, rails, hardware, and labor separated out, and the number on the invoice at the end is the number you approved up front. Every fence job carries our Done Right Promise: if a post shifts, a gate sticks, or a picket splits in that first year, we come back and make it right. The follow-up visit is covered.
Call (831) 604-3426 and we’ll schedule a time to walk the fence line, measure, and hand you a written estimate. No phone tag, no four-hour waiting windows.
DIY or Call Us?
Replacing a split picket or tightening a loose latch is straightforward enough to do yourself. But setting fence posts is where DIY projects in Ventura go sideways, and here’s the specific reason: most homeowners dig a 2-foot hole, set the post, and call it done. Ventura building code wants fence posts below grade at least one-third the above-ground height, and in clay soil that swells and shrinks with the seasons, a shallow post will lean by the second winter.
A post that’s shifting or a panel that’s rotted at the rail needs a saw, a post-hole digger, framing square, and a level, plus disposal of the old concrete. It’s physical, repetitive work, and if you set a post even two degrees out of plumb, the whole section will show it. If you’re not sure whether your post is salvageable, call us at (831) 604-3426 and we’ll tell you over the phone what we think it’ll take. The estimate is free either way.
FAQs

A well-set KraftMaid fence will last 15 to 25 years in Ventura, with posts being the first thing to go. Coastal fog and the marine layer keep the wood damp longer than inland climates, so expect posts on the west side of your property to need replacing five to seven years before everything else.
Yes, if the rot is limited to the top few inches and the concrete footer is still solid, we can cut the post flat, bolt a post bracket, and mount on top. If the base is soft or the footing is cracked, the post needs to come out and a new one goes in. Call (831) 604-3426 and we’ll give you the straight answer after looking at it.
A typical Ventura fence replacement with 4 to 6 new posts takes one to two days. If we’re doing a full perimeter and a gate with new hardware, plan on three days including concrete cure time before the gate goes back on. You’ll get a schedule in writing before we start.
We stock common gate hinge brackets, latch kits, and stainless rail brackets that match KraftMaid’s size specs on hand, so most repairs don’t wait on parts. If you need a specific KraftMaid part number, we can order it direct and have the job done within the week.
If your KraftMaid fence is leaning, splitting, or the gate won’t close, call (831) 604-3426 for a free estimate. We’ll walk the fence line with you, price it in writing, and tell you exactly what’s worth saving. The work says it. We just show up and cut straight.
Written by Sawyer Remodel Ventura, Sawyer Remodel Ventura at Sawyer Remodel Ventura, serving Ventura and nearby areas.


