







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Kitchen Remodeling: The Ventura Owner’s Guide
CGI kitchen remodeling in Ventura typically runs $14,000 to $45,000 for a full renovation, and that’s the honest spread we quote before any demo starts. If you’re reading this, you probably have a CGI-built kitchen that’s showing its age: delaminating cabinet faces, worn-out drawer slides, a layout that fought you from day one, or countertops that lost their finish three years ago. We handle the whole replacement, from pulling the old boxes to setting the new ones, and we stock the common parts on hand so we’re not running back and forth across Ventura Boulevard mid-job.
CGI kitchens weren’t built as a system you patch forever. They were spec’d to a price point, and when one part fails, the rest usually isn’t far behind. The good news: the bones are often fine, and a full rework costs less than you’d think when you’re not paying for surprises. We price it in writing before we touch anything.
Key Takeaways:
- Full CGI kitchen remodel in Ventura: $14,000 – $45,000 installed
- We’re an independent contractor, not affiliated with CGI, and we match specs from their standard build sheets
- Most CGI failures trace to the same things: cabinet boxes, drawer hardware, and laminate surfaces
- Written price before work starts, Done Right Promise on every job
Which CGI Models This Applies To

CGI kitchens came out of California’s production-home boom, and Ventura has plenty of them, from the East End tracts up to the hillside builds off Foothill Road. The cabinets were typically shop-built, frameless or face-frame depending on the development, and the hardware was mid-grade at best. The drawer slides and hinges are the usual failure points, followed by the thermofoil or laminate doors that peel at the edges. If you open a drawer and the slide grinds or the face wiggles, that’s the CGI standard hardware giving up after 15 to 25 years of daily use.
Here’s the compatibility gotcha most owners hit: CGI jobs used at least two different cabinet series depending on the subdivision phase, and the door profiles don’t always swap cleanly between them. The standard 3/4-inch box depth is consistent, but the hinge boring, drawer width, and rail spacing can vary by half an inch. That’s why we don’t just order “CGI replacement doors” and hope. We pull one box, measure the bore pattern and the overlay, and match the new pieces to what’s actually there. For aftermarket replacements, we source through KraftMaid and Wellborn when the geometry lines up, and we tell you plainly when OEM-equivalent is the better call. On the countertop side, if you had CGI’s standard laminate with a rolled front edge, most homeowners upgrade to Cambria or Silestone quartz during the rework because the old laminate isn’t worth saving once the cabinets come out.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Kitchen Remodeling Is Failing
- Drawer slides sticking or grinding: The original CGI hardware was light-duty, and after years of daily use the ball bearings wear flat. The drawer still moves, but it’s fighting you, and one day it’ll jump the track and drop. That’s the slide, not the drawer box, and replacing the hardware is the fix.
- Door edges peeling or bubbling: Thermofoil and laminate doors delaminate when heat and moisture work into the edge banding. Ventura’s coastal humidity accelerates it, especially on the cabinets nearest the stove and sink. Once the edge lifts, water gets in and the MDF core swells. It won’t flatten back out.
- Hinges sagging or screws stripping out: The original hinge plates were screwed into particleboard with short screws. Over time the holes wallow out, the door drops, and you can’t tighten it back. New hinges with longer screws and proper pilot holes solve it, but only if the box is still sound.
- Countertop seams separating near the sink: CGI’s laminate counters weren’t sealed well at the seams, and water intrusion lifts the substrate. You’ll see a dark line, a soft spot, or a slight ridge along the seam. That’s not a cosmetic problem. It’s rot starting, and it only spreads.
- Cabinet boxes pulling away from the wall: The upper cabinets were hung on screws into studs, but the boxes themselves flex under load. If you see a gap opening at the top of an upper, or the cabinet creaks when you open a full drawer, the box is losing its integrity. Don’t load it with heavy dishes and wait to see what happens.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

In Ventura, a full CGI kitchen remodel with us lands between $14,000 and $45,000. That’s the installed range, not a materials-only teaser. A smaller galley kitchen with stock KraftMaid cabinets, laminate counters, and a basic backsplash runs toward the bottom of that spread. A larger cook’s kitchen with custom or semi-custom Wellborn boxes, Cambria quartz, a tile backsplash, and new island plumbing and electrical runs toward the top. The spread comes down to cabinet grade, countertop material, and whether we’re moving walls or utilities.
Every quote is written, itemized, and fixed before we start. No change orders because we missed something on the estimate. Our parts come with the manufacturer’s warranty, and our labor is covered by the Done Right Promise: if something that was installed fails inside a year, we come back and make it right at no charge. The price you approve is the price on the invoice, period.
For smaller, targeted fixes inside the same kitchen, the numbers break out like this:
- Cabinet installation only: $4,000 – $13,000
- Countertop installation only: $2,000 – $6,500
- Backsplash installation: $800 – $2,500
- Kitchen island installation: $3,000 – $10,000
DIY or Call Us?
For this kind of work, the honest answer is call us. Replacing cabinet hardware is one thing. Pulling out screwed-in boxes, re-leveling them, and setting countertops is another. The dangerous part isn’t the blades. It’s the weight. Upper cabinets full of dishes falling on you, a granite slab slipping off its shims, a box you thought was anchored tearing loose mid-pull. We’ve seen the aftermath, and it’s never worth the money saved.
What you can reasonably check on your own: open every drawer and door, look for the signs above, and take photos. That helps us give you a ballpark over the phone before we even send someone out. Then call (831) 604-3426 for a free estimate. We’ll show up, look at what’s there, and hand you a written number. If it’s out of budget, we’ll tell you what can wait and what can’t.
FAQs

Most full CGI kitchen remodels in Ventura take three to six weeks from demo to final walkthrough. Smaller jobs like cabinet and countertop replacement run one to two weeks. Custom cabinet orders add three to five weeks of lead time before we even start, and we’ll tell you that upfront so you can plan around it. Call (831) 604-3426 and we’ll give you a timeline for your specific kitchen.
Sometimes, yes. If the boxes are square and the problem is hardware, we can swap slides, hinges, and door fronts for far less than a full tear-out. But if the boxes are water-damaged, separating, or pulling from the wall, repairs just delay the replacement and you’ll spend the money twice. After we inspect, we’ll tell you straight which path makes sense for your kitchen in Ventura.
A small CGI kitchen remodel in Ventura typically runs $9,000 to $20,000. That includes new cabinet faces or full boxes, countertops, and hardware for a compact layout. The final number depends on cabinet type and countertop material. Call (831) 604-3426 for a written quote, not a guess.
We stock common replacement hardware, hinges, drawer slides, and edge materials on hand, and we pull from local suppliers for KraftMaid, Cambria, Silestone, and Wellborn product lines. For CGI-specific components, we measure and match to what’s in your kitchen rather than ordering blind. Estimates are free, so call (831) 604-3426 and we’ll come take a look.
Written by Sawyer Remodel Ventura, Sawyer Remodel Ventura at Sawyer Remodel Ventura, serving Ventura and nearby areas.


