







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Driveway & Pavers: The Ventura Owner's Guide
CGI driveway and paver parts in Ventura typically run $180 to $640 installed depending on the component, and most swaps are done in one visit. The catch with CGI is that parts aren't universal – paver thickness, edge restraint profiles, and the underlayment system all have to match what went in originally, or the repair fails fast. Most homeowners find out a part has failed the hard way: a paver sinks after rain, an edge restraint pops loose near the garage apron, or a section of the driveway starts shifting and grinding against its neighbor.
We stock common CGI-compatible driveway and paver components on hand and can source the rest within a day or two through our supply network. If you're staring at a sunken paver or a cracked edge piece in Ventura, here's what you need to know before anyone touches it.
Sawyer Remodel Ventura is an independent service provider. We're not affiliated with CGI – we just work on their products regularly and know how they behave in this climate.
Which CGI Models This Applies To

CGI produces a few distinct paver lines, and the part you need depends on which one is under your feet. The three most common we see around Ventura are the standard interlocking concrete paver (usually 60mm thick), the permeable paver system, and the slab-style paver used for larger driveway runs. The 60mm interlocking unit is by far the most common in residential driveways here. Permeable versions look similar but have wider joint gaps and a different base-spec – you can't swap them interchangeably without changing how water drains.
Here's the compatibility gotcha most people miss: CGI pavers are modular, meaning their width-to-length ratio locks into a specific pattern. Grab a paver from a different series or a different manufacturer and the joints won't line up. The pattern walks. Within six months you'll see drifted lines and uneven gaps. When we match CGI parts, we measure the actual unit – not just nominal size – because even a 3mm difference across a 20-foot driveway compounds into visible misalignment by the time you reach the street.
For the OEM-vs-aftermarket call: OEM CGI pavers guarantee color and dimension match, which matters most on a visible driveway. Quality aftermarket equivalents cost roughly 20-30% less and work fine for less visible areas or as a temporary patch, but you'll usually see the difference in aggregate color under direct sun. For edge restraints and base materials, we use premium aftermarket products without hesitation – the OEM markup there buys you nothing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Driveway & Pavers Is Failing
- Sinking or depressed pavers near the edges. This is almost always a base failure – Ventura's clay-heavy soil shifts with winter moisture, and if the compacted base wasn't thick enough, it settles. The paver itself is usually fine; the ground under it wasn't.
- Edge restraint pulling away at the driveway apron. The plastic or aluminum edging that pins the outer pavers gets hit by car tires and sun-baked over time. Once it flexes loose, the outer course of pavers spreads and the whole edge starts to drift.
- Cracks running through individual pavers. A hairline crack in one or two units usually means a point load exceeding what the 60mm thickness can take – a delivery truck, an RV, or a heavy vehicle parked in the same spot repeatedly. It's rare in pedestrian-only areas.
- Joint sand washing out after every rain. If you're sweeping sand back into the joints more than twice a season, the edge restraint or the bedding layer has failed somewhere and water is channeling through instead of draining evenly.
- Pavers rocking or clicking when you step on them. That's loose bedding sand under the unit. One or two rockers is a 20-minute fix. A whole section of rockers usually means the base is compromised and needs more than a sand top-up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What's Included

For a CGI-specific driveway or paver repair in Ventura, here's the price picture we give before anyone commits:
- Single paver replacement: $180 to $320
- Edge restraint repair (per 10 linear feet): $220 to $420
- Section re-leveling (up to 50 sq ft): $450 to $950
- Full paver driveway replacement: $7,000 to $18,000
- Paver patio installation (new): $3,500 to $11,000
The range depends on what we find underneath. A straight paver swap with solid base is cheap. A paver that sank because the sub-base was never compacted properly in 2011? That's a different job. Your written price includes the part, labor, joint sand, any base repair, and haul-away of the old material. No change orders unless you authorize them. The workmanship is covered under our Done Right Promise – if a repair fails within a year, we come back and make it right, free.
DIY or Call Us?
Pavers are one of the safer driveway repairs to attempt – there's no high-tension spring or live wiring here. What you can safely check: is the paver intact but rocking, and is the edge restraint still tight? If yes, you might get away with pulling the paver, adding bedding sand, and tapping it back level with a rubber mallet. What goes wrong in DIY: removing a paver without the right lift tool chips the adjacent units, tamping without a plate compactor leaves a low spot that returns in two months, and matching a CGI paver by eye at a big-box store gets you a color drift you'll notice every single day you park on it. If the issue is edge restraint, base settlement, or more than three adjacent pavers, call (831) 604-3426. You'll get a straight answer and a written price before we touch anything.
FAQs

With a properly compacted base, CGI concrete pavers last 25 to 40 years in Ventura's climate – the paver itself rarely fails. What fails first in coastal California is the base and edge restraint, typically within 10 to 15 years if drainage was marginal from day one. Call (831) 604-3426 and we'll tell you honestly which part of the system is failing.
A cracked paver can sometimes be stabilized with a color-matched epoxy patch, but if the crack runs full-depth, replacement is the only repair that lasts. In direct sun, patch material weathers at a different rate than the paver and a visible repair mark becomes obvious within a year or two. We'll show you both options with the price difference in writing.
A single paver or small edge repair is done in about an hour and drivable the same day. A section re-leveling takes half a day. A full driveway replacement in Ventura runs 3 to 7 days depending on square footage and base condition. We give you the timeline in writing before work starts, not after we've started digging.
We keep common 60mm CGI-compatible pavers, edge restraints, and joint sand on hand, so typical repairs happen on the first visit. Special-order colors or permeable-system parts usually arrive within 2 to 3 business days. Call (831) 604-3426 with your paver dimensions and a photo, and we'll confirm availability before we schedule.
Written by Sawyer Remodel Ventura, Sawyer Remodel Ventura at Sawyer Remodel Ventura, serving Ventura and nearby areas.


