







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Kitchen Remodeling: The Ventura Owner’s Guide
Kitchen remodeling around ES Windows in Ventura runs $14,000 to $45,000 installed, depending on how much of the opening we’re rebuilding and what surrounds the window. Most calls we get start with a homeowner noticing water staining below the sill or a crank that’s gone stiff in a house built in the 90s or 2000s, when ES Windows were a common spec in Ventura tract homes. Here’s the reality: window work is almost never just window work. The sill, the drywall returns, the countertop overhang, the backsplash line that dies into the frame – it’s all connected. When an ES window fails in a kitchen, the repair usually turns into a partial remodel because the surrounding surfaces have to come apart to do the job right.
That’s why we price it as a kitchen remodel, not a window swap. The window is the trigger. The kitchen is the scope.
Which ES Windows Models This Applies To

ES Windows were made in several series that show up all over Ventura – the ES-3000 single-hung, the ES-5000 casement, and the ES-7000 slider are the big three we see in kitchens built between roughly 1985 and 2010. Each series used different frame depths and different sash hardware, so a replacement part from one series does not drop into another. That’s the first compatibility gotcha: ES Windows parts are series-specific, and the labels are often worn off by decades of sun exposure this close to the coast.
If you can’t read the label, we match by measuring the visible glass width, the frame depth at the sill, and the shape of the crank housing if it’s a casement. ES-5000 casements used a distinctive square crank base; the older ES-3000 used a round one. The second gotcha: ES Windows used aluminum frames with a thermal break that degrades differently in Ventura’s salt air than it does inland. That break is what fails first, and once it’s gone, the frame conducts heat and cold straight through. OEM parts are getting scarce for the ES-3000 line. Quality aftermarket equivalents exist for most hardware and weatherstripping, but we won’t put an aftermarket sash balancer in a kitchen window that faces the afternoon marine layer – it’ll sag within a year. We spec OEM when the part is structural and aftermarket only when it’s trim or weatherstripping.
We should be clear: Sawyer Remodel Ventura is an independent contractor. We stock and install ES Windows-compatible parts, but we’re not affiliated with ES Windows or their distributor network. We source through our own supply channels and stand behind what we install.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your ES Windows Kitchen Remodeling Is Failing
- Water staining or soft drywall under the sill. The weep holes on ES aluminum frames clog with salt and grit in Ventura, and water backs up into the wall cavity. By the time you see the stain on the inside, the sill framing underneath is usually already wet.
- The crank turns but the sash doesn’t move. That’s a stripped operator gear in the ES-5000 casement line. The gear teeth are pot metal and they shear clean off after about 15 years of regular use.
- Condensation between the panes in the morning. The factory seal on the insulated glass unit has failed. Ventura’s daily temperature swing – especially in neighborhoods like Midtown where morning marine layer burns off fast – accelerates seal failure. Once the seal is gone, the glass fogs and you’re replacing the IGU, not the whole window.
- A kitchen window that won’t stay open or slams shut. That’s the block-and-tackle balancer in a single-hung ES-3000. The nylon cord in those balancers frays over time, and when it lets go, the sash can drop hard. If you’ve got kids, that’s a finger hazard.
- You can feel a draft standing at the sink in winter. The felt weatherstripping in the ES-3000 and ES-7000 series rots out after about 8 to 10 years, faster within a mile of the beach. Salt air makes the felt brittle. Replacements are cheap, but getting the frame clean enough for the new strip to seat properly is the part people skip – and that’s why the draft comes back.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

In Ventura, a kitchen remodel that revolves around an ES Windows replacement lands between $14,000 and $45,000. Here’s what drives the spread:
| Scope | Typical Ventura Price |
|---|---|
| Window only (part, trim, no surrounding work) | $4,500 – $15,000 |
| Window + sill rebuild + drywall returns | $14,000 – $22,000 |
| Window + backsplash + countertop section | $22,000 – $35,000 |
| Full kitchen remodel with ES Windows replacement | $35,000 – $45,000 |
The window itself is the cheap part in most of these jobs. The labor is in the surrounding surfaces – pulling the backsplash without cracking the field tile, templating the countertop to the new sill depth, matching the finish on a 30-year-old cabinet run. We write the price before we start, and it includes the part, the labor, the disposal, and the written Done Right Promise on the whole scope. If the window gets swapped and the surrounding work isn’t right, we’re back to make it right. That’s in writing.
DIY or Call Us?
You can safely do two things yourself: clean the tracks and weep holes with a stiff brush and a shop vac, and take photos of any labels or stamping on the frame so you know exactly what you’re working with. That’s where DIY stops for ES Windows. These are aluminum-frame windows with spring-loaded balances and, on the casements, a tensioned operator arm. If the balance lets go while you’re prying the sash out, it can break a hand. If you drop the IGU, you’re buying a new one and cleaning glass out of your kitchen for a week.
What we tell Ventura homeowners is this: run the test, take the photos, call us. We’ll match the part off your measurements, bring the right hardware the first trip, and the quote is free. Call (831) 604-3426 and we’ll walk you through what you’re looking at.
FAQs

You should get 20 to 30 years out of an ES Aluminum frame in Ventura’s climate, but the seals, weatherstripping, and hardware wear out faster – usually at the 10 to 15 year mark. If the window is on a south- or west-facing wall, the sun ages the thermal break faster. Call (831) 604-3426 and we can tell you over the phone whether it’s a part fix or a full replacement based on what you’re seeing.
Usually yes if the frame is not bowed and the thermal break is intact. Balancers, crank gears, weatherstripping, and IGUs can all be swapped. The frame itself is the deciding line – once the aluminum is twisted or the thermal break is gone, replacement is the only fix that lasts. Estimates are free, so it costs you nothing to find out which side of the line you’re on.
A window-only swap is a one-day job. Adding a sill rebuild and drywall returns pushes it to two or three days. If we’re tying into backsplash and countertop, plan for two to three weeks across the full sequence. The window itself goes in on day one, and we button up the surrounding finishes behind it. Call (831) 604-3426 and we’ll give you a straight timeline for your specific setup.
We carry the common hardware – crank operators for the ES-5000, block-and-tackle balancers for the ES-3000, and weatherstripping for both – on hand, so we’re ready for most Ventura kitchen calls the same trip. IGUs and full sashes are built to spec and take three to five days. If you’re not sure what’s failed, we’ll identify it on the first visit and have the right part in hand when we come back to install.
No. The written price you approve before we start is the price on the invoice. If we open the wall and find something we genuinely couldn’t have seen from the outside, we stop, show you photos, and get your sign-off on the change before we spend another dollar. No surprises at the invoice. That’s the Relay Visibility Guarantee, and it’s on every job we do in Ventura.
We work alongside KraftMaid cabinetry, Cambria and Silestone surfaces, and other proven material partners when the kitchen work extends beyond the window. The work says it. We just show up and cut straight.
Written by Sawyer Remodel Ventura, Sawyer Remodel Ventura at Sawyer Remodel Ventura, serving Ventura and nearby areas.


