A Sawyer company - serving Ventura, CA
A remodeled kitchen with a wood island, painted cabinets and a plaster range hood

Barrette Kitchen Remodeling Nationwide

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansA Local Team in Ventura
New painted shaker cabinets with an organized deep drawer
A small remodeled galley kitchen with cabinets to the ceiling
A walk-in pantry with wood shelving
A remodeled kitchen with a waterfall island and wood cabinets
A remodeled kitchen with painted cabinets and a farmhouse sink
A wide opening with a new beam where the kitchen wall was removed
A remodeled hall bathroom with subway tile and a floating vanity
A remodeled primary suite with built-in wardrobes and a window seat
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Barrette Kitchen Remodeling: The Ventura Owner’s Guide

Barrette kitchen remodeling parts and hardware in Ventura typically run $90 to $600 for the component itself, with full installation and finish work landing between $14,000 and $45,000 depending on scope. We stock the common Barrette-compatible cabinet hardware, drawer slides, hinges, and trim pieces on hand, so most single-part replacements in Ventura are a one-visit job. The usual discovery is quiet: a drawer that sticks, a hinge that’s gone floppy, or a cabinet face that’s cracked along the grain where the California sun dries things out faster than the manufacturer expected.

Call (831) 604-3426

Which Barrette Models This Applies To

Barrette’s kitchen line runs through three main series in our Ventura service area: the Classic series (flat-panel doors, 3/8-inch overlay hinges), the Everyday series (soft-close drawers, 1/2-inch overlay), and the newer Studio collection with modular cabinets that use a pin-and-shelf system. The compatibility gotcha most Ventura homeowners hit is the hinge spec: Barrette switched from 35mm cup hinges to 40mm on Studio and late-run Everyday models in 2022, and the old 35mm hinge won’t seat on the new bore. Measure the cup hole before ordering anything. For drawer slides, Barrette uses 18-inch and 21-inch lengths, and a 21 won’t fit an 18-inch cabinet box no matter how much cussing is applied. We match exact OEM Barrette parts when the cabinet is still under warranty, and we’ll spec equivalent Blum or Grass hardware when it isn’t. Both are what Barrette’s own factories have used as suppliers at different points, so aftermarket usually means same plant, different box.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Barrette Kitchen Remodeling Is Failing

  • Drawers that don’t close flush, or bounce back open. The soft-close dampener inside the slide has blown its o-ring, a $25 part we replace in under an hour. Left alone, the misalignment will start wearing the drawer box itself.
  • Cabinet doors that hang lower on one side every few months. The hinge’s adjustment screw has stripped in the particleboard, and repeated retightening just reams the hole wider. A new hinge plate with a bigger thread is the actual fix.
  • Cracked or peeling veneer on door faces, especially west-facing kitchens in Ventura. Coastal air and afternoon heat cycle the thermofoil until it separates from the MDF core. Refinishing never holds; replacement faces do.
  • Missing shelf pins or collapsed shelves. The Studio series uses a two-piece pin-and-cup system, and when the cup cracks, the shelf drops onto the one below it. We’ve seen whole cabinet interiors taken out by a single failed cup.
  • Hardware that’s corroded, pitted, or flaking around the handles. Salt air off the Pacific meets cheap zinc die-cast pulls and the finish loses within a couple of years. It’s cosmetic until a pull snaps off in your hand mid-open.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A single Barrette part replacement in Ventura, hinge or slide or shelf hardware, runs $90 to $200 installed when we can match it on hand. A full hardware swap across a 20-door kitchen lands between $600 and $1,400 depending on hinge count and slide length. When the failure is structural, cracked faces, water-swollen cabinet boxes, or the whole kitchen’s run its course, we quote the full remodel at $14,000 to $45,000. Every quote is a written, line-item price before any work starts. That’s the part where you see exactly what the parts cost, what the labor costs, and what you’re approving. The Done Right Promise backs every replacement: if the new hinge sags, the drawer binds, or the face cracks, we come back and make it right. No invoice surprises, no argument.

DIY or Call Us?

Most Barrette hardware failures are genuinely simple swaps if you know the cup size and slide length, and we’re happy to save you a trip charge on a two-minute job by walking you through what to check over the phone. That said, hinge work on cabinets that carry stone counters is a different risk: the wrong bore placement or an over-tightened screw into a cabinet box that’s already softened from a plumbing leak can cascade into countertop cracking, and a cracked Caesarstone or Cambria top is a far bigger bill than a hinge. When in doubt, call (831) 604-3426, text us a photo of the failed part, and we’ll tell you straight whether it’s a truck-stock swap or a full repair visit. Most calls take under five minutes and we’ll tell you the price before we send anyone out.

FAQs

Installers leveling a new base cabinet during a kitchen remodel

Getting started with Sawyer in Ventura

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead measuring a kitchen with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A remodeling crew arriving at a home with lumber and tools

Your Ventura team

A local vetted partner works across Ventura and the towns around it, to the same written standard as every Sawyer job.

Areas we serve
A worker laying floor protection and a dust barrier before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help in Ventura? Licensed & insured · free written estimates
Call (831) 604-3426
Local Service Coverage

Request a Free Estimate in Ventura

Tell us what you need - Sawyer Remodel Ventura responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch