







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Fence Installation: The Ventura Owner’s Guide
A full CWS fence installation in Ventura runs $3,500 to $9,000 installed, including removal of the old fence, new posts set in concrete, rails, pickets, and hardware. For a partial repair or section replacement, most homeowners in Ventura pay $1,200 to $3,800 depending on how many panels failed and what condition the posts are in. Most owners figure out something’s wrong the same way: a gate that drags, a section of fence leaning after a Santa Ana wind event, or pickets that have started cupping and pulling off the rails. We carry CWS-compatible fence parts on hand and can usually have a section back up within a few days, not weeks.
Note: Sawyer Remodel Ventura is an independent contractor. We are not affiliated with CWS, but we install and repair CWS fence systems throughout Ventura with parts matched to the original specs.
Which CWS Models This Applies To

CWS fence systems come in a few distinct lines, and matching parts to the right series matters more than most homeowners expect. The big split is between CWS wood privacy fences and CWS ornamental iron or aluminum styles. Wood systems use either 1×4 or 1×6 dog-ear pickets on 2×4 rails, with posts typically set at 6-foot or 8-foot spacing depending on the original install. Metal systems use ¾-inch pickets with punched channel rails, and the post caps and gate hinges are series-specific. If you’ve got a CWS fence, you’ll usually find a small stamp or sticker on the inside of the gate frame or on the top rail. If that’s gone, measure the picket width and post spacing before buying parts. A 1×4 picket is not interchangeable with a 1×6, and forcing the swap looks wrong and fails early.
When it comes to OEM versus aftermarket, our rule in Ventura is simple: for structural rails, posts, and gate frames, go OEM or exact-match. The tolerances on CWS gate hardware are tight, and a knock-off hinge that’s off by an eighth of an inch turns a smooth gate into one that binds every time the temperature shifts. For pickets and trim, a quality aftermarket board from a local Ventura lumber yard often beats the OEM on price and holds up just as well, as long as it’s the same species and dried properly.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Fence Installation Is Failing
- Posts leaning or twisting. The concrete footer was too shallow for the post height, or water has been sitting at the base. In Ventura’s marine layer zones, we see this most often along back fences that never get direct sun, so the soil stays damp year-round.
- Pickets cupping, splitting, or falling off. This is a fastener problem. Nails back out as the wood swells and shrinks through Ventura’s wet-dry cycles, and once the bottom nail lets go, the picket warps and pops off the rail.
- Rails sagging between posts. Usually a span issue, or too-small rails for the span. CWS wood sections need a 2×4 rail at minimum, and any span over 6 feet really should have a mid-rail or a thicker top rail.
- Gate dragging or refusing to latch. The post has moved, or the hinge screws have eaten themselves loose. Forcing the gate only tears the hinge out of the post, which turns a $40 repair into a post replacement.
- Bottom of pickets rotting through. Wood sitting in wet soil or too close to sprinkler heads. In Ventura, this shows up fastest on the north side of a fence, where the morning marine layer and shade from the house keep the base wet for hours.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s how CWS fence installation costs shake out in Ventura:
- Full CWS wood fence installation: $3,500 – $9,000 depending on linear feet, post spacing, gate count, and soil conditions.
- Partial section replacement (1 – 3 panels): $1,200 – $3,800 including post reset and new pickets where needed.
- Post replacement: $200 – $450 per post including concrete removal and new footer, with variables for soil type and access.
- Gate replacement with CWS-compatible hardware: $450 – $1,100 per gate, including frame, hinges, and latch.
Every price we give in Ventura is written before we touch a tool, and it includes removal of the old section, haul-away of debris, concrete for post footers, all hardware, and a workmanship warranty. No change orders on material cost once we’ve looked at the job. If a post is set and the gate still binds three months later, that’s covered under the Done Right Promise.
DIY or Call Us?
You can absolutely reset a sagging gate hinge or replace a few loose pickets yourself if you have a level, a drill, and an afternoon. What you shouldn’t DIY is anything involving a post set in concrete, especially on a slope or in clay-heavy Ventura soil. A snapped post under tension from a heavy gate can take a fence section down hard. The same goes for removing a concrete footer with a fence still attached to it.
For most Ventura homeowners, the time cost is the deciding factor. A three-panel repair takes us a day. The same job on a weekend with one trip to the hardware store and one trip back for the right post mix usually burns two weekends. If you’d rather skip the guessing, call us at (831) 604-3426 and we’ll price the section, tell you exactly what we’re matching, and schedule it.
FAQs

A CWS wood fence in Ventura typically lasts 15 to 25 years, depending on sun exposure, drainage, and whether the posts were set deep enough. In coastal neighborhoods with heavy morning marine layer, the bottom rail and picket ends usually fail first, often by year 12 to 15. For an exact assessment of your fence, call (831) 604-3426 and we’ll walk it with you.
Yes. If the posts are sound and the rot is limited to pickets or one rail, we can replace just those parts and leave the rest of the fence untouched. Most partial repairs in Ventura run $1,200 to $3,800. We won’t sell you a full replacement if the repair will hold. Call (831) 604-3426 for a free look.
Most CWS fence section replacements take one to two days in Ventura, including post removal, new concrete, and rail and picket installation. Concrete needs a day to set before we hang anything heavy on a gate post. We’ll tell you the exact timeline when we see the job.
We keep common CWS-compatible components on hand: rails, pickets in 1×4 and 1×6, gate hinges, latches, and post caps. For any parts we don’t have, we source from local Ventura suppliers, typically within one to two business days. Call (831) 604-3426 with your measurements and we’ll confirm what’s on hand before we schedule.
Written by Sawyer Remodel Ventura, Sawyer Remodel Ventura at Sawyer Remodel Ventura, serving Ventura and nearby areas.


