A Sawyer company - serving Ventura, CA
A remodeled kitchen with a wood island, painted cabinets and a plaster range hood

Schluter Kitchen Remodeling Nationwide

Free Estimate on SiteCalls Answered by a Live Person, 24/7Background-Checked TechniciansA Local Team in Ventura
New painted shaker cabinets with an organized deep drawer
A small remodeled galley kitchen with cabinets to the ceiling
A walk-in pantry with wood shelving
A remodeled kitchen with a waterfall island and wood cabinets
A remodeled kitchen with painted cabinets and a farmhouse sink
A built-in window seat in a bay window
A dining nook with a built-in banquette
A home office with a built-in desk and shelves
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Kitchen Remodeling: The Ventura Owner’s Guide

A full Schluter kitchen remodel in Ventura runs $14,000 to $45,000 installed, depending on cabinet layout, countertop choice, and how much waterproofing the Schluter system needs to cover. We stock Schluter-compatible materials on hand and can usually start within a week of your estimate. Most homeowners discover they need us when the previous waterproofing fails: grout cracking along the countertop line, tiles loosening near the sink, or water staining the cabinet face beneath the dishwasher.

Call (831) 604-3426

Schluter does one thing better than nearly anyone in the tile world: waterproofing. If your kitchen remodel involves tile, and that tile touches water, Schluter is the system underneath that keeps water out of your cabinets, subfloor, and walls. When it’s installed correctly, it lasts decades. When it isn’t, the failure shows up fast, and it shows up wet.

Which Schluter Models This Applies To

Installers leveling a new base cabinet during a kitchen remodel

Schluter makes a full kitchen lineup: Ditra and Ditra-Heat underlayment for floors, Kerdi-Board for walls and backsplashes, Kerdi-Band for seams, and the profile edge trims (Rondec, Quadec, Jolly) that finish tile edges. Each has a specific job. Each fails differently.

The compatibility gotcha most homeowners hit: Ditra and Ditra-Heat are not interchangeable without planning. Ditra-Heat is thinner where the heating cable sits, and it requires a dedicated circuit from your panel. If you buy Ditra-Heat expecting warm floors but your electrical panel has no open breaker and your subfloor is 3/4-inch plywood over 16-inch joist spacing, you’re doing panel work first. That’s a budget line item most online tutorials skip. The second gotcha is edge trim sizing: Schluter profiles are measured by tile thickness plus thinset depth. Order the trim too shallow and the tile lip sits proud. Too deep and you see a grout line no one wanted. We measure on site, every time.

OEM versus aftermarket matters less for Schluter membranes than for trim. The membranes are a system: Kerdi-Band overlaps Kerdi-Board at 2 inches minimum, and you can’t swap a knockoff seam tape and expect the waterproofing warranty to hold. For profile trims, quality aluminum aftermarket pieces work fine if the wall depth matches. We’ll tell you where you can save and where you shouldn’t. Sawyer Remodel Ventura is an independent contractor, not a Schluter dealer or affiliate, so we recommend based on what holds up, not what moves inventory.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Kitchen Remodeling Is Failing

  • Grout cracking along the countertop-to-backsplash seam. This is movement, not age. Schluter profiles should absorb that movement. If the grout keeps cracking, the wrong trim was used or none was.
  • Tiles sounding hollow when tapped near the sink. The thinset has lost bond. When that happens over Ditra, water has usually worked into the fleece layer, which means the waterproofing did its job but the tile layer failed.
  • Water staining on the cabinet face under the dishwasher or sink. The Schluter layer is either missing, incorrectly seamed, or the dishwasher drain is leaking behind the toekick. We find this a lot in older Ventura homes where the original install predates membrane systems entirely.
  • Tile edges chipping at the profile transition. That’s usually impact damage or a profile that’s a half-size too shallow. Once the edge starts going, the tile follows because it’s lost its mechanical lock.
  • Warm floors in one spot, cold six inches away. Ditra-Heat cable failure or a poorly laid mat. If the cable’s broken, the mat’s done for most cases, and we’re pulling floor tile to fix it.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

A finished basement family room with a media wall and wet bar

A Schluter kitchen remodel in Ventura runs $14,000 to $45,000. A smaller galley kitchen often lands between $9,000 and $20,000. Backsplash-only work with Schluter waterproofing runs $800 to $2,500. Countertop replacement sits at $2,000 to $6,500. Cabinet installation adds $4,000 to $13,000, and an island $3,000 to $10,000.

What drives the spread: cabinet quality (KraftMaid and Wellborn are our go-to lines), countertop stone (Cambria, Silestone, Caesarstone), footage of tile, whether you’re adding heated floors, and how much demolition the existing space needs. We price in writing before any work starts. The number you approve is the number on the invoice. Our Done Right Promise covers the workmanship for a full year after closeout, and if a repair fails during that window, the second visit is free.

DIY or Call Us?

You can check your own tile with a quarter and your knuckles: tap, listen, and mark hollow spots. You can also slide a thin feeler gauge along the countertop seam to see how deep the grout has failed. What you shouldn’t do is pull up a Schluter membrane yourself. Once that fleece layers loses bond or you cut into a heating cable, you’ve doubled the repair cost. A broken Ditra-Heat cable is not a splice-and-tape job. It’s a code-sensitive electrical repair, and it needs a proper circuit check. Call us at (831) 604-3426. We’ll open it up carefully, tell you what’s actually wrong, and quote the fix before we pick up a tool.

FAQs

A powder room with botanical wallpaper and a stone sink

Getting started with Sawyer in Ventura

Every project starts with a conversation and a written price. Here is how to take the first step.

A project lead measuring a kitchen with the homeowner during a free estimate

Free on-site estimate

A project lead walks the job with you, measures it and hands you a written, line-item price. No obligation.

Book an estimate
A remodeling crew arriving at a home with lumber and tools

Your Ventura team

A local vetted partner works across Ventura and the towns around it, to the same written standard as every Sawyer job.

Areas we serve
A worker laying floor protection and a dust barrier before work starts

Read our written promise

What we promise on every job, written down, with the terms spelled out before any work starts.

Our promise
Need Construction help in Ventura? Licensed & insured · free written estimates
Call (831) 604-3426
Local Service Coverage

Request a Free Estimate in Ventura

Tell us what you need - Sawyer Remodel Ventura responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch